4.0mm Heavy Gauge Hot Dip Galvanized W Beam Guardrail Plate AASHTO M180 Highway Guardrail
Product Details
| Beam Profile: | W Beam, Two Wave | Plate Thickness: | 4.0mm |
|---|---|---|---|
| Steel Grade: | Q235B, Tensile 375-500 MPa | Beam Length: | 4320mm Standard, Cut To Order |
| Face Width: | 312mm | Beam Depth: | 83mm |
| Zinc Coating: | Hot Dip, Min 600 G/m2 | Hole Pattern: | AASHTO Standard Slots For Blockout |
| Standard: | AASHTO M180, ASTM A123 | ||
| Highlight |
4.0mm Heavy Gauge W Beam Guardrail Plate,Hot Dip Galvanized Highway Guardrail,AASHTO M180 W Beam Guardrail Plate |
||
Product Description
W beam guardrail plate in 4.0mm heavy gauge is the section specified where traffic speeds and vehicle weights sit at the top of the semi-rigid barrier range: national expressways, freight corridors, toll plaza approaches and bridge approach ramps. Each plate is cold roll-formed from Q235B strip into the standard two-wave profile, precision punched for blockouts and lap splices, and then hot dip galvanized to a minimum 600 g/m2 zinc mass, roughly 85 microns. That coating sits well above the AASHTO M180 minimum and leaves a deep reserve against sand abrasion, salt spray and de-icing chemicals.
Key Features- 4.0mm heavy gauge plate: roughly 25 percent more steel than a 3.2mm plate, raising bending resistance and section modulus so the barrier holds its line under heavier impact without increasing post density.
- 600 g/m2 hot dip zinc: applied after all punching and cutting, so every slot edge and plate end is sealed, which is where thin coatings fail first on coastal and desert routes.
- Constant wave geometry: formed on automated roll lines with fixed roll sets, keeping face width at 312mm and beam depth at 83mm from the first plate in the run to the last.
- AASHTO hole pattern: slotted for standard blockouts and overlap bolts, so plates mate with existing stock and no field re-drilling is needed on a live carriageway.
- Traceable steel: each heat number is recorded against the container load, with mill certificate and zinc mass report issued per lot for engineer inspection.
- Cut to length service: non-standard lengths for bridge transitions, toll lanes and curve sections are rolled and galvanized with the main order, avoiding a second coating batch and a visible shade difference.
| Parameter | Specification |
|---|---|
| Beam profile | W beam, two wave |
| Plate thickness | 4.0mm |
| Steel grade | Q235B, tensile strength 375-500 MPa |
| Beam length | 4320mm standard, cut lengths on request |
| Face width | 312mm |
| Beam depth | 83mm |
| Zinc coating | Hot dip, minimum 600 g/m2 |
| Hole pattern | Standard slots for blockout and lap bolts |
| Fasteners | M16 galvanized bolts, grade 8.8 |
| Standard | AASHTO M180, ASTM A123 |
The heavy gauge plate is chosen for high speed rural and urban expressways, truck routes and container corridors where the proportion of heavy goods vehicles is high. It also suits toll plaza approach gantries, weigh station lanes and sections where a barrier cannot be set back far from the running lane. In coastal and desert regions the heavy zinc coating extends inspection intervals and keeps the plate within specification at annual coating audits.
Packaging & Quality AssurancePlates are bundled in units of 25 to 30 pieces, steel strapped with corner protectors to stop zinc damage in transit, and loaded into 40HQ containers with timber dunnage between bundles. Bundles are marked with heat number, plate thickness and quantity so the site team can match deliveries to chainage without opening every pack.
Before shipment each lot passes dimensional checks on face width, depth, straightness and hole position, plus coating mass testing on samples cut from the production run. Reports for both are issued with the shipping documents, and rejected lots are never split into later containers. We support third party inspection and can hold material for the client's nominated surveyor at no extra handling cost.
Product Highlights
4.0mm heavy gauge W beam guardrail plate in Q235B, hot dip galvanized 600 g/m2 to AASHTO M180, punched for standard blockouts, 4320mm standard length.
Hot Dip Galvanized Steel Grating Checkered Plate Compound Heavy Duty Grating
Hot Dip Galvanized Composite Steel Grating | Checkered Plate Compound Grating Product Overview Hot Dip Galvanized Composite Steel Grating is a high-performance sealed steel flooring and drainage solution combining a welded steel grating base with a galvanized checkered anti-slip plate through full ...
Hot Dip Galvanized Q235 Steel Two Wave Guardrail AASHTO M180 Road Safety Guardrail
Hot Dip Galvanized Q235 Steel Two Wave Guardrail AASHTO M180 Road Safety Guardrail Galvanized W-beam Guardrail Two Wave Guardrail, also known as Double Wave W Beam Guardrail, is a semi-rigid traffic safety barrier widely used for highways, roads, bridges, ramps, parking lots and scenic areas. It is ...
Progressive Beam Lowering Terminal End Section with Deformable Energy Absorption and Left Hand or Right Hand Directional Build for Thrie Beam Guardrail
Energy absorbing terminal end section for thrie beam guardrail, cold roll-formed and galvanized, lowers the beam to ground level at the barrier run-out.
Please use our online inquiry contact form below if you have any questions, our team will get back to you as soon as possible.